Storage Daemon Configuration

The Bareos Storage Daemon configuration file has relatively few resource definitions. However, due to the great variation in backup media and system capabilities, the storage daemon must be highly configurable. As a consequence, there are quite a large number of directives in the Device Resource definition that allow you to define all the characteristics of your Storage device (normally a tape drive). Fortunately, with modern storage devices, the defaults are sufficient, and very few directives are actually needed.

For a general discussion of configuration file and resources including the data types recognized by Bareos, please see the Configuration chapter of this manual. The following Storage Resource definitions must be defined:

Storage – to define the name of the Storage daemon.
Director – to define the Director’s name and its access password.
Device – to define the characteristics of your storage device (tape drive).
Messages – to define where error and information messages are to be sent.

Following resources are optional:

Autochanger Resource – to define Autochanger devices.
NDMP Resource – to define the NDMP authentication context.

Storage Resource

In general, the properties specified under the Storage resource define global properties of the Storage daemon. Each Storage daemon configuration file must have one and only one Storage resource definition.

configuration directive name	type of data	default value	remark
`Absolute Job Timeout (Sd->Storage)`	= `PINT32`
`Allow Bandwidth Bursting (Sd->Storage)`	= `BOOLEAN`	no
`Auto XFlate On Replication (Sd->Storage)`	= `BOOLEAN`	no
`Backend Directory (Sd->Storage)`	= `DIRECTORY_LIST`	/usr/lib/bareos/backends (platform specific)
`Checkpoint Interval (Sd->Storage)`	= `TIME`	0
`Client Connect Wait (Sd->Storage)`	= `TIME`	1800
`Collect Device Statistics (Sd->Storage)`	= `BOOLEAN`	no	deprecated
`Collect Job Statistics (Sd->Storage)`	= `BOOLEAN`	no	deprecated
`Description (Sd->Storage)`	= `STRING`
`Device Reserve By Media Type (Sd->Storage)`	= `BOOLEAN`	no
`Enable kTLS (Sd->Storage)`	= `BOOLEAN`	no
`FD Connect Timeout (Sd->Storage)`	= `TIME`	1800
`File Device Concurrent Read (Sd->Storage)`	= `BOOLEAN`	no
`Heartbeat Interval (Sd->Storage)`	= `TIME`	0
`Just In Time Reservation (Sd->Storage)`	= `BOOLEAN`	No
`Log Timestamp Format (Sd->Storage)`	= `STRING`	%d-%b %H:%M
`Maximum Bandwidth Per Job (Sd->Storage)`	= `SPEED`
`Maximum Concurrent Jobs (Sd->Storage)`	= `PINT32`	20
`Maximum Network Buffer Size (Sd->Storage)`	= `PINT32`
`Messages (Sd->Storage)`	= `RES`
`Name (Sd->Storage)`	= `NAME`		required
`NDMP Address (Sd->Storage)`	= `ADDRESS`	10000
`NDMP Addresses (Sd->Storage)`	= `ADDRESSES`	10000
`NDMP Enable (Sd->Storage)`	= `BOOLEAN`	no
`NDMP Log Level (Sd->Storage)`	= `PINT32`	4
`NDMP Port (Sd->Storage)`	= `PORT`	10000
`NDMP Snooping (Sd->Storage)`	= `BOOLEAN`	no
`Plugin Directory (Sd->Storage)`	= `DIRECTORY`
`Plugin Names (Sd->Storage)`	= `PLUGIN_NAMES`
`Scripts Directory (Sd->Storage)`	= `DIRECTORY`
`SD Address (Sd->Storage)`	= `ADDRESS`	9103
`SD Addresses (Sd->Storage)`	= `ADDRESSES`	9103
`SD Connect Timeout (Sd->Storage)`	= `TIME`	1800
`SD Port (Sd->Storage)`	= `PORT`	9103
`SD Source Address (Sd->Storage)`	= `ADDRESS`	0
`Secure Erase Command (Sd->Storage)`	= `STRING`
`Statistics Collect Interval (Sd->Storage)`	= `PINT32`	0	deprecated
`TLS Allowed CN (Sd->Storage)`	= `STRING_LIST`
`TLS Authenticate (Sd->Storage)`	= `BOOLEAN`	no
`TLS CA Certificate Dir (Sd->Storage)`	= `DIRECTORY`
`TLS CA Certificate File (Sd->Storage)`	= `DIRECTORY`
`TLS Certificate (Sd->Storage)`	= `DIRECTORY`
`TLS Certificate Revocation List (Sd->Storage)`	= `DIRECTORY`
`TLS Cipher List (Sd->Storage)`	= `STRING`
`TLS Cipher Suites (Sd->Storage)`	= `STRING`
`TLS DH File (Sd->Storage)`	= `DIRECTORY`
`TLS Enable (Sd->Storage)`	= `BOOLEAN`	yes
`TLS Key (Sd->Storage)`	= `DIRECTORY`
`TLS Protocol (Sd->Storage)`	= `STRING`
`TLS Require (Sd->Storage)`	= `BOOLEAN`	yes
`TLS Verify Peer (Sd->Storage)`	= `BOOLEAN`	no
`Ver Id (Sd->Storage)`	= `STRING`
`Working Directory (Sd->Storage)`	= `DIRECTORY`	/var/lib/bareos (platform specific)

Absolute Job Timeout

Type:: PINT32
Since Version:: 14.2.0

Absolute time after which a Job gets terminated regardless of its progress

Allow Bandwidth Bursting

Type:: BOOLEAN
Default value:: no

Auto XFlate On Replication

Type:: BOOLEAN
Default value:: no
Since Version:: 13.4.0

This directive controls the autoxflate-sd plugin plugin when replicating data inside one or between two storage daemons (Migration/Copy Jobs). Normally the storage daemon will use the autoinflate/autodeflate setting of the device when reading and writing data to it which could mean that while reading it inflates the compressed data and the while writing the other deflates it again. If you just want the data to be exactly the same e.g. don’t perform any on the fly uncompression and compression while doing the replication of data you can set this option to no and it will override any setting on the device for doing auto inflation/deflation when doing data replication. This will not have any impact on any normal backup or restore jobs.

Backend Directory

Type:: DIRECTORY_LIST
Default value:: /usr/lib/bareos/backends (platform specific)

Checkpoint Interval

Type:: TIME
Default value:: 0

This is the interval at which Backup checkpoints are executed.

For more information about checkpoints, check the Checkpoints chapter.

Client Connect Wait

Type:: TIME
Default value:: 1800

This directive defines an interval of time in seconds that the Storage daemon will wait for a Client (the File daemon) to connect. Be aware that the longer the Storage daemon waits for a Client, the more resources will be tied up.

Collect Device Statistics

Type:: BOOLEAN
Default value:: no
Since Version:: deprecated

Collect Job Statistics

Type:: BOOLEAN
Default value:: no
Since Version:: deprecated

Description

Type:: STRING

Device Reserve By Media Type

Type:: BOOLEAN
Default value:: no

Enable kTLS

Type:: BOOLEAN
Default value:: no

If set to “yes”, Bareos will allow the SSL implementation to use Kernel TLS.

FD Connect Timeout

Type:: TIME
Default value:: 1800

File Device Concurrent Read

Type:: BOOLEAN
Default value:: no

Heartbeat Interval

Type:: TIME
Default value:: 0

Optional and if specified set a keepalive interval (heartbeat) on the sockets used by the defined Bareos Storage Daemon.

See details in Heartbeat Interval - TCP Keepalive.

Just In Time Reservation

Type:: BOOLEAN
Default value:: No
Since Version:: 23.1.0

The storage daemon will only reserve devices when it receives data that needs to be written. This option also means that no session label gets written if the job is empty.

Log Timestamp Format

Type:: STRING
Default value:: %d-%b %H:%M
Since Version:: 15.2.3

This parameter needs to be a valid strftime format string. See man 3 strftime for the full list of available substitution variables.

Maximum Bandwidth Per Job

Type:: SPEED

Maximum Concurrent Jobs

Type:: PINT32
Default value:: 20

This directive specifies the maximum number of Jobs that may run concurrently. Each contact from the Director (e.g. status request, job start request) is considered as a Job, so if you want to be able to do a status request in the console at the same time as a Job is running, you will need to set this value greater than 1. To run simultaneous Jobs, you will need to set a number of other directives in the Director’s configuration file. Which ones you set depend on what you want, but you will almost certainly need to set the Maximum Concurrent Jobs (Dir->Storage). Please refer to the Concurrent Jobs chapter.

Maximum Network Buffer Size

Type:: PINT32

where bytes specifies the initial network buffer size to use with the File daemon. This size will be adjusted down if it is too large until it is accepted by the OS. Please use care in setting this value since if it is too large, it will be trimmed by 512 bytes until the OS is happy, which may require a large number of system calls. The default value is 256KiB.

It is recommended to not set this value unless necessary. If necessary you should set this to the bandwidth delay product of your network. For example if your fd is connected to the sd through a Gigabit connection (e.g. 128MiB/s bandwidth) and the connection has a latency of 4ms, then the BDP of that connection is 128MiB/s * 4ms = 512KiB, if the connection has a latency of 32ms, then the BDP is 128MiB/s * 32ms = 4MiB.

You will probably also want to make the corresponding change in each of your File daemons conf files.

Warning

Setting this variable may disable your operating systems dynamic network buffering schema. This could cause performance degradation and excessive memory use. Use with care.

Messages

Type:: RES

Name

Required:: True
Type:: NAME

Specifies the Name of the Storage daemon.

NDMP Address

Type:: ADDRESS
Default value:: 10000

This directive is optional, and if it is specified, it will cause the Storage daemon server (for NDMP Tape Server connections) to bind to the specified IP-Address, which is either a domain name or an IP address. If it is not specified, the Storage Daemon will bind to both IPv6 and IPv4 default addresses (the default).

NDMP Addresses

Type:: ADDRESSES
Default value:: 10000

Specify the ports and addresses on which the Storage daemon will listen for NDMP Tape Server connections. Normally, the default is sufficient and you do not need to specify this directive.

NDMP Enable

Type:: BOOLEAN
Default value:: no

This directive enables the Native NDMP Tape Agent.

NDMP Log Level

Type:: PINT32
Default value:: 4

This directive sets the loglevel for the NDMP protocol library.

NDMP Port

Type:: PORT
Default value:: 10000

Specifies port number on which the Storage daemon listens for NDMP Tape Server connections.

By default, the Storage daemon server (for NDMP Tape Server connections) will listen to both IPv6 and IPv4 default addresses on the port you set. If you want to listen on either IPv4 or IPv6 only, you have to specify it with either NDMP Address (Sd->Storage), or remove NDMP Port (Sd->Storage)and just use NDMP Addresses (Sd->Storage)instead.

NDMP Snooping

Type:: BOOLEAN
Default value:: no

This directive enables the Snooping and pretty printing of NDMP protocol information in debugging mode.

Plugin Directory

Type:: DIRECTORY

This directive specifies a directory in which the Storage Daemon searches for plugins with the name <pluginname>-sd.so which it will load at startup.

Plugin Names

Type:: PLUGIN_NAMES

If a Plugin Directory (Sd->Storage) is specified Plugin Names defines, which Storage Daemon Plugins get loaded.

If Plugin Names is not defined, all plugins get loaded, otherwise the defined ones.

Scripts Directory

Type:: DIRECTORY

This directive is currently unused.

SD Address

Type:: ADDRESS
Default value:: 9103

This directive is optional, and if it is specified, it will cause the Storage daemon server (for Director and File daemon connections) to bind to the specified IP-Address, which is either a domain name or an IP address. If this and the SD Addresses (Sd->Storage) directives are not specified, the Storage Daemon will bind to both IPv6 and IPv4 default addresses (the default).

SD Addresses

Type:: ADDRESSES
Default value:: 9103

Specify the ports and addresses on which the Storage daemon will listen for Director connections. Using this directive, you can replace both the SD Port (Sd->Storage) and SD Address (Sd->Storage) directives.

SD Connect Timeout

Type:: TIME
Default value:: 1800

SD Port

Type:: PORT
Default value:: 9103

Specifies port number on which the Storage daemon listens for Director connections.

By default, the Storage Daemon will listen to both IPv6 and IPv4 default addresses on the port you set. If you want to listen on either IPv4 or IPv6 only, you have to specify it with either SD Address (Sd->Storage), or remove SD Port (Sd->Storage)and just use SD Addresses (Sd->Storage)instead.

SD Source Address

Type:: ADDRESS
Default value:: 0

Secure Erase Command

Type:: STRING
Since Version:: 15.2.1

Specify command that will be called when bareos unlinks files.

When files are no longer needed, Bareos will delete (unlink) them. With this directive, it will call the specified command to delete these files. See Secure Erase Command for details.

Statistics Collect Interval

Type:: PINT32
Default value:: 0
Since Version:: deprecated

TLS Allowed CN

Type:: STRING_LIST

“Common Name”s (CNs) of the allowed peer certificates.

TLS Authenticate

Type:: BOOLEAN
Default value:: no

Use TLS only to authenticate, not for encryption.

TLS CA Certificate Dir

Type:: DIRECTORY

Path of a TLS CA certificate directory.

TLS CA Certificate File

Type:: DIRECTORY

Path of a PEM encoded TLS CA certificate(s) file.

TLS Certificate

Type:: DIRECTORY

Path of a PEM encoded TLS certificate.

TLS Certificate Revocation List

Type:: DIRECTORY

Path of a Certificate Revocation List file.

TLS Cipher List

Type:: STRING

Colon separated list of valid TLSv1.2 and lower Ciphers; see “openssl ciphers” command. Leftmost element has the highest priority.

TLS Cipher Suites

Type:: STRING

Colon separated list of valid TLSv1.3 Ciphers; see “openssl ciphers -s -tls1_3” command. Leftmost element has the highest priority. Currently only SHA256 ciphers are supported.

TLS DH File

Type:: DIRECTORY

Path to PEM encoded Diffie-Hellman parameter file. If this directive is specified, DH key exchange will be used for the ephemeral keying, allowing for forward secrecy of communications.

TLS Enable

Type:: BOOLEAN
Default value:: yes

Enable TLS support.

Bareos can be configured to encrypt all its network traffic. Chapter TLS Configuration Directives explains how the Bareos components must be configured to use TLS.

TLS Key

Type:: DIRECTORY

Path of a PEM encoded private key. It must correspond to the specified “TLS Certificate”.

TLS Protocol

Type:: STRING
Since Version:: 20.0.0

OpenSSL Configuration: Protocol

TLS Require

Type:: BOOLEAN
Default value:: yes

If set to “no”, Bareos can fall back to use unencrypted connections.

TLS Verify Peer

Type:: BOOLEAN
Default value:: no

If disabled, all certificates signed by a known CA will be accepted. If enabled, the CN of a certificate must the Address or in the “TLS Allowed CN” list.

Ver Id

Type:: STRING

Working Directory

Type:: DIRECTORY
Default value:: /var/lib/bareos (platform specific)

This directive specifies a directory in which the Storage daemon may put its status files. This directory should be used only by Bareos, but may be shared by other Bareos daemons provided the names given to each daemon are unique.

The following is a typical Storage daemon storage resource definition.

Storage daemon storage definition

#
# "Global" Storage daemon configuration specifications appear
# under the Storage resource.
#
Storage {
  Name = "Storage daemon"
  Address = localhost
}

Director Resource

The Director resource specifies the Name of the Director which is permitted to use the services of the Storage daemon. There may be multiple Director resources. The Director Name and Password must match the corresponding values in the Director’s configuration file.

configuration directive name	type of data	default value	remark
`Description (Sd->Director)`	= `STRING`
`Enable kTLS (Sd->Director)`	= `BOOLEAN`	no
`Key Encryption Key (Sd->Director)`	= `AUTOPASSWORD`
`Maximum Bandwidth Per Job (Sd->Director)`	= `SPEED`
`Monitor (Sd->Director)`	= `BOOLEAN`
`Name (Sd->Director)`	= `NAME`		required
`Password (Sd->Director)`	= `AUTOPASSWORD`		required
`TLS Allowed CN (Sd->Director)`	= `STRING_LIST`
`TLS Authenticate (Sd->Director)`	= `BOOLEAN`	no
`TLS CA Certificate Dir (Sd->Director)`	= `DIRECTORY`
`TLS CA Certificate File (Sd->Director)`	= `DIRECTORY`
`TLS Certificate (Sd->Director)`	= `DIRECTORY`
`TLS Certificate Revocation List (Sd->Director)`	= `DIRECTORY`
`TLS Cipher List (Sd->Director)`	= `STRING`
`TLS Cipher Suites (Sd->Director)`	= `STRING`
`TLS DH File (Sd->Director)`	= `DIRECTORY`
`TLS Enable (Sd->Director)`	= `BOOLEAN`	yes
`TLS Key (Sd->Director)`	= `DIRECTORY`
`TLS Protocol (Sd->Director)`	= `STRING`
`TLS Require (Sd->Director)`	= `BOOLEAN`	yes
`TLS Verify Peer (Sd->Director)`	= `BOOLEAN`	no

Description

Type:: STRING

Enable kTLS

Type:: BOOLEAN
Default value:: no

If set to “yes”, Bareos will allow the SSL implementation to use Kernel TLS.

Key Encryption Key

Type:: AUTOPASSWORD

This key is used to encrypt the Security Key that is exchanged between the Director and the Storage Daemon for supporting Application Managed Encryption (AME). For security reasons each Director should have a different Key Encryption Key.

Maximum Bandwidth Per Job

Type:: SPEED

Monitor

Type:: BOOLEAN

If Monitor is set to no (default), this director will have full access to this Storage daemon. If Monitor is set to yes, this director will only be able to fetch the current status of this Storage daemon.

Please note that if this director is being used by a Monitor, we highly recommend to set this directive to yes to avoid serious security problems.

Name

Required:: True
Type:: NAME

Specifies the Name of the Director allowed to connect to the Storage daemon. This directive is required.

Password

Required:: True
Type:: AUTOPASSWORD

Specifies the password that must be supplied by the above named Director. This directive is required.

TLS Allowed CN

Type:: STRING_LIST

“Common Name”s (CNs) of the allowed peer certificates.

TLS Authenticate

Type:: BOOLEAN
Default value:: no

Use TLS only to authenticate, not for encryption.

TLS CA Certificate Dir

Type:: DIRECTORY

Path of a TLS CA certificate directory.

TLS CA Certificate File

Type:: DIRECTORY

Path of a PEM encoded TLS CA certificate(s) file.

TLS Certificate

Type:: DIRECTORY

Path of a PEM encoded TLS certificate.

TLS Certificate Revocation List

Type:: DIRECTORY

Path of a Certificate Revocation List file.

TLS Cipher List

Type:: STRING

Colon separated list of valid TLSv1.2 and lower Ciphers; see “openssl ciphers” command. Leftmost element has the highest priority.

TLS Cipher Suites

Type:: STRING

Colon separated list of valid TLSv1.3 Ciphers; see “openssl ciphers -s -tls1_3” command. Leftmost element has the highest priority. Currently only SHA256 ciphers are supported.

TLS DH File

Type:: DIRECTORY

Path to PEM encoded Diffie-Hellman parameter file. If this directive is specified, DH key exchange will be used for the ephemeral keying, allowing for forward secrecy of communications.

TLS Enable

Type:: BOOLEAN
Default value:: yes

Enable TLS support.

Bareos can be configured to encrypt all its network traffic. Chapter TLS Configuration Directives explains how the Bareos components must be configured to use TLS.

TLS Key

Type:: DIRECTORY

Path of a PEM encoded private key. It must correspond to the specified “TLS Certificate”.

TLS Protocol

Type:: STRING
Since Version:: 20.0.0

OpenSSL Configuration: Protocol

TLS Require

Type:: BOOLEAN
Default value:: yes

If set to “no”, Bareos can fall back to use unencrypted connections.

TLS Verify Peer

Type:: BOOLEAN
Default value:: no

If disabled, all certificates signed by a known CA will be accepted. If enabled, the CN of a certificate must the Address or in the “TLS Allowed CN” list.

The following is an example of a valid Director resource definition:

Storage daemon Director definition

Director {
  Name = MainDirector
  Password = my_secret_password
}

NDMP Resource

The NDMP Resource specifies the authentication details of each NDMP client. There may be multiple NDMP resources for a single Storage daemon. In general, the properties specified within the NDMP resource are specific to one client.

configuration directive name	type of data	default value	remark
`Auth Type (Sd->Ndmp)`	= `AUTH_TYPE`	None
`Description (Sd->Ndmp)`	= `STRING`
`Log Level (Sd->Ndmp)`	= `PINT32`	4
`Name (Sd->Ndmp)`	= `NAME`		required
`Password (Sd->Ndmp)`	= `AUTOPASSWORD`		required
`Username (Sd->Ndmp)`	= `STRING`		required

Auth Type

Type:: AUTH_TYPE
Default value:: None

Specifies the authentication type that must be supplied by the above named NDMP Client. This directive is required.

The following values are allowed:

None - Use no password
Clear - Use clear text password
MD5 - Use MD5 hashing

Description

Type:: STRING

Log Level

Type:: PINT32
Default value:: 4

Specifies the NDMP Loglevel which overrides the global NDMP loglevel for this client.

Name

Required:: True
Type:: NAME

Specifies the name of the NDMP Client allowed to connect to the Storage daemon. This directive is required.

Password

Required:: True
Type:: AUTOPASSWORD

Specifies the password that must be supplied by the above named NDMP Client. This directive is required.

Username

Required:: True
Type:: STRING

Specifies the username that must be supplied by the above named NDMP Client. This directive is required.

Device Resource

The Device Resource specifies the details of each device (normally a tape drive) that can be used by the Storage daemon. There may be multiple Device resources for a single Storage daemon. In general, the properties specified within the Device resource are specific to the Device.

configuration directive name	type of data	default value	remark
`Access Mode (Sd->Device)`	= `IO_DIRECTION`	readwrite
`Alert Command (Sd->Device)`	= `STRNAME`
`Always Open (Sd->Device)`	= `BIT`	yes
`Archive Device (Sd->Device)`	= `STRNAME`		required
`Auto Deflate (Sd->Device)`	= `IO_DIRECTION`
`Auto Deflate Algorithm (Sd->Device)`	= `COMPRESSION_ALGORITHM`
`Auto Deflate Level (Sd->Device)`	= `PINT16`	6
`Auto Inflate (Sd->Device)`	= `IO_DIRECTION`
`Auto Select (Sd->Device)`	= `BOOLEAN`	yes
`Autochanger (Sd->Device)`	= `BIT`	no
`Automatic Mount (Sd->Device)`	= `BIT`	no
`Backward Space File (Sd->Device)`	= `BIT`	yes
`Backward Space Record (Sd->Device)`	= `BIT`	yes
`Block Checksum (Sd->Device)`	= `BIT`	yes
`Block Positioning (Sd->Device)`	= `BIT`	yes
`Bsf At Eom (Sd->Device)`	= `BIT`	no
`Changer Command (Sd->Device)`	= `STRNAME`
`Changer Device (Sd->Device)`	= `STRNAME`
`Check Labels (Sd->Device)`	= `BIT`	no	deprecated
`Close On Poll (Sd->Device)`	= `BIT`	no
`Collect Statistics (Sd->Device)`	= `BOOLEAN`	yes
`Count (Sd->Device)`	= `PINT32`	1
`Description (Sd->Device)`	= `STRING`
`Device Options (Sd->Device)`	= `STRING`
`Device Type (Sd->Device)`	= `STRING`
`Diagnostic Device (Sd->Device)`	= `STRNAME`
`Drive Crypto Enabled (Sd->Device)`	= `BOOLEAN`
`Drive Index (Sd->Device)`	= `PINT16`
`Drive Tape Alert Enabled (Sd->Device)`	= `BOOLEAN`
`Eof On Error Is Eot (Sd->Device)`	= `BOOLEAN`
`Fast Forward Space File (Sd->Device)`	= `BIT`	yes
`Forward Space File (Sd->Device)`	= `BIT`	yes
`Forward Space Record (Sd->Device)`	= `BIT`	yes
`Hardware End Of File (Sd->Device)`	= `BIT`	yes
`Hardware End Of Medium (Sd->Device)`	= `BIT`	yes
`Label Block Size (Sd->Device)`	= `PINT32`	64512
`Label Media (Sd->Device)`	= `BIT`	no
`Label Type (Sd->Device)`	= `LABEL`		deprecated
`Maximum Block Size (Sd->Device)`	= `MAX_BLOCKSIZE`	1048576
`Maximum Changer Wait (Sd->Device)`	= `TIME`	300
`Maximum Concurrent Jobs (Sd->Device)`	= `PINT32`	1
`Maximum File Size (Sd->Device)`	= `SIZE64`	1000000000
`Maximum Job Spool Size (Sd->Device)`	= `SIZE64`
`Maximum Network Buffer Size (Sd->Device)`	= `PINT32`
`Maximum Open Volumes (Sd->Device)`	= `PINT32`	1
`Maximum Open Wait (Sd->Device)`	= `TIME`	300
`Maximum Rewind Wait (Sd->Device)`	= `TIME`	300
`Maximum Spool Size (Sd->Device)`	= `SIZE64`
`Media Type (Sd->Device)`	= `STRNAME`		required
`Minimum Block Size (Sd->Device)`	= `PINT32`
`Mount Command (Sd->Device)`	= `STRNAME`
`Mount Point (Sd->Device)`	= `STRNAME`
`Name (Sd->Device)`	= `NAME`		required
`No Rewind On Close (Sd->Device)`	= `BOOLEAN`	yes
`Offline On Unmount (Sd->Device)`	= `BIT`	no
`Query Crypto Status (Sd->Device)`	= `BOOLEAN`
`Random Access (Sd->Device)`	= `BIT`	no
`Removable Media (Sd->Device)`	= `BIT`	yes
`Requires Mount (Sd->Device)`	= `BIT`	no
`Spool Directory (Sd->Device)`	= `DIRECTORY`
`Two Eof (Sd->Device)`	= `BIT`	no
`Unmount Command (Sd->Device)`	= `STRNAME`
`Use Mtiocget (Sd->Device)`	= `BIT`	yes
`Volume Capacity (Sd->Device)`	= `SIZE64`
`Volume Poll Interval (Sd->Device)`	= `TIME`	300

Access Mode

Type:: IO_DIRECTION
Default value:: readwrite

Access mode specifies whether this device can be reserved for reading, writing or for both modes (default).

The following values are valid:

readonly - this device can be reserved only for reading.
writeonly - this device can be reserved only for writing.
readwrite - this device can be reserved for both reading and writing.

Alert Command

Type:: STRNAME

This specifies an external program to be called at the completion of each Job after the device is released. The purpose of this command is to check for Tape Alerts, which are present when something is wrong with your tape drive (at least for most modern tape drives). The same substitution characters that may be specified in the Changer Command may also be used in this string. For more information, see the Autochanger & Tape drive Support chapter.

Note, it is not necessary to have an autochanger to use this command. The example below uses the tapeinfo program that comes with the mtx package, but it can be used on any tape drive. However, you will need to specify a Changer Device (Sd->Device) directive so that the generic SCSI device name can be edited into the command (with the %c).

An example of the use of this command to print Tape Alerts in the Job report is:

Alert Command = "sh -c 'tapeinfo -f %c | grep TapeAlert'"

and an example output when there is a problem could be:

bareos-sd  Alert: TapeAlert[32]: Interface: Problem with SCSI interface
                  between tape drive and initiator.

Always Open

Type:: BIT
Default value:: yes

If Yes, Bareos will always keep the device open unless specifically unmounted by the Console program. This permits Bareos to ensure that the tape drive is always available, and properly positioned. If you set AlwaysOpen to no Bareos will only open the drive when necessary, and at the end of the Job if no other Jobs are using the drive, it will be freed. The next time Bareos wants to append to a tape on a drive that was freed, Bareos will rewind the tape and position it to the end. To avoid unnecessary tape positioning and to minimize unnecessary operator intervention, it is highly recommended that Always Open = yes. This also ensures that the drive is available when Bareos needs it.

If you have Always Open = yes (recommended) and you want to use the drive for something else, simply use the unmount command in the Console program to release the drive. However, don’t forget to remount the drive with mount when the drive is available or the next Bareos job will block.

For File storage, this directive is ignored. For a FIFO storage device, you must set this to No.

Please note that if you set this directive to No Bareos will release the tape drive between each job, and thus the next job will rewind the tape and position it to the end of the data. This can be a very time consuming operation. In addition, with this directive set to no, certain multiple drive autochanger operations will fail. We strongly recommend to keep Always Open set to Yes

Archive Device

Required:: True
Type:: STRNAME

Specifies where to read and write the backup data. The type of the Archive Device can be specified by the Device Type (Sd->Device) directive. If Device Type is not specified, Bareos tries to guess the Device Type accordingly to the type of the specified Archive Device file type.

There are different types that are supported:

device: Usually the device file name of a removable storage device (tape drive), for example /dev/nst0 or /dev/rmt/0mbn, preferably in the “non-rewind” variant. In addition, on systems such as Sun, which have multiple tape access methods, you must be sure to specify to use Berkeley I/O conventions with the device. The b in the Solaris (Sun) archive specification /dev/rmt/0mbn is what is needed in this case. Bareos does not support SysV tape drive behavior.
directory: If a directory is specified, it is used as file storage. The directory must be existing and be specified as absolute path. Bareos will write to file storage in the specified directory and the filename used will be the Volume name as specified in the Catalog. If you want to write into more than one directory (i.e. to spread the load to different disk drives), you will need to define two Device resources, each containing an Archive Device with a different directory.

fifo

A FIFO is a special kind of file that connects two programs via kernel memory. If a FIFO device is specified for a backup operation, you must have a program that reads what Bareos writes into the FIFO. When the Storage daemon starts the job, it will wait for Maximum Open Wait (Sd->Device) seconds for the read program to start reading, and then time it out and terminate the job. As a consequence, it is best to start the read
program at the beginning of the job perhaps with the Run Before Job (Dir->Job) directive. For this kind of device, you always want to specify Always Open (Sd->Device) = no, because you want the Storage daemon to open it only when a job starts. Since a FIFO is a one way device, Bareos will not attempt to read a label of a FIFO device, but will simply write on it. To create a FIFO Volume in the catalog, use the add command rather than the label command to avoid attempting to write a label.
Device {
  Name = FifoStorage
  Media Type = Fifo
  Device Type = Fifo
  Archive Device = /tmp/fifo
  LabelMedia = yes
  Random Access = no
  AutomaticMount = no
  RemovableMedia = no
  MaximumOpenWait = 60
  AlwaysOpen = no
}
During a restore operation, if the Archive Device is a FIFO, Bareos will attempt to read from the FIFO, so you must have an external program that writes into the FIFO. Bareos will wait Maximum Open Wait (Sd->Device) seconds for the program to begin writing and will then time it out and terminate the job. As noted above, you may use the Run Before Job (Dir->Job) to start the writer program at the beginning of the job.

A FIFO device can also be used to test your configuration, see the Howto section.

GlusterFS Storage

don’t use this directive, but only Device Type (Sd->Device) and Device Options (Sd->Device) (this behavior have changed with Version >= 15.2.0).

Ceph Object Store

don’t use this directive, but only Device Type (Sd->Device) and Device Options (Sd->Device). (this behavior have changed with Version >= 15.2.0).

Auto Deflate

Type:: IO_DIRECTION
Since Version:: 13.4.0

This is a parameter used by autoxflate-sd which allow you to transform a non compressed piece of data into a compressed piece of data on the storage daemon. e.g. Storage Daemon compression. You can either enable compression on the client and use the CPU cyclces there to compress your data with one of the supported compression algorithms. The value of this parameter specifies a so called io-direction currently you can use the following io-directions:

in - compress data streams while reading the data from a device.
out - compress data streams while writing the data to a device.
both - compress data streams both when reading and writing to a device.

Currently only plain data streams are compressed (so things that are already compressed or encrypted will not be considered for compression.) Also meta-data streams are not compressed. The compression is done in a way that the stream is transformed into a native compressed data stream. So if you enable this and send the data to a filedaemon it will know its a compressed stream and will do the decompression itself. This also means that you can turn this option on and off at any time without having any problems with data already written.

This option could be used if your clients doesn’t have enough power to do the compression/decompression itself and you have enough network bandwidth. Or when your filesystem doesn’t have the option to transparently compress data you write to it but you want the data to be compressed when written.

Auto Deflate Algorithm

Type:: COMPRESSION_ALGORITHM
Since Version:: 13.4.0

This option specifies the compression algorithm used for the autodeflate option which is performed by the autoxflate-sd plugin. The algorithms supported are:

GZIP - gzip level 1–9
LZO
LZFAST
LZ4
LZ4HC

Auto Deflate Level

Type:: PINT16
Default value:: 6
Since Version:: 13.4.0

This option specifies the level to be used when compressing when you select a compression algorithm that has different levels.

Auto Inflate

Type:: IO_DIRECTION
Since Version:: 13.4.0

This is a parameter used by autoxflate-sd which allow you to transform a compressed piece of data into a non compressed piece of data on the storage daemon. e.g. Storage Daemon decompression. You can either enable decompression on the client and use the CPU cyclces there to decompress your data with one of the supported compression algorithms. The value of this parameter specifies a so called io-direction currently you can use the following io-directions:

in - decompress data streams while reading the data from a device.
out - decompress data streams while writing the data to a device.
both - decompress data streams both when reading and writing to a device.

This option allows you to write uncompressed data to for instance a tape drive that has hardware compression even when you compress your data on the client with for instance a low cpu load compression method (LZ4 for instance) to transfer less data over the network. It also allows you to restore data in a compression format that the client might not support but the storage daemon does. This only works on normal compressed datastreams not on encrypted datastreams or meta data streams.

Auto Select

Type:: BOOLEAN
Default value:: yes

If this directive is set to yes, and the Device belongs to an autochanger, then when the Autochanger is referenced by the Director, this device can automatically be selected. If this directive is set to no, then the Device can only be referenced by directly using the Device name in the Director. This is useful for reserving a drive for something special such as a high priority backup or restore operations.

It is possible to temporarily set this directive using the console command setdevice.

Autochanger

Type:: BIT
Default value:: no

If set to yes, this device belongs to an automatic tape changer, and you must specify an Autochanger resource that points to this Device resource.

If set to no, the volume must be manually changed.

In the Bareos Director, the directive Auto Changer (Dir->Storage) should be set in correspondence.

Automatic Mount

Type:: BIT
Default value:: no

If yes, permits the daemon to examine the device to determine if it contains a Bareos labeled volume. This is done initially when the daemon is started, and then at the beginning of each job. This directive is particularly important if you have set Always Open (Sd->Device) = no because it permits Bareos to attempt to read the device before asking the system operator to mount a tape. However, please note that the tape must be mounted before the job begins.

Backward Space File

Type:: BIT
Default value:: yes

If Yes, the archive device supports the MTBSF and MTBSF ioctls to backspace over an end of file mark and to the start of a file. If No, these calls are not used and the device must be rewound and advanced forward to the desired position.

Backward Space Record

Type:: BIT
Default value:: yes

If Yes, the archive device supports the tt MTBSR ioctl to backspace records. If No, this call is not used and the device must be rewound and advanced forward to the desired position. This function if enabled is used at the end of a Volume after writing the end of file and any ANSI/IBM labels to determine whether or not the last block was written correctly. If you turn this function off, the test will not be done. This causes no harm as the re-read process is precautionary rather than required.

Block Checksum

Type:: BIT
Default value:: yes

You may turn off the Block Checksum (CRC32) code that Bareos uses when writing blocks to a Volume. Doing so can reduce the Storage daemon CPU usage slightly. It will also permit Bareos to read a Volume that has corrupted data.

It is not recommend to turn this off, particularly on older tape drives or for disk Volumes where doing so may allow corrupted data to go undetected.

Block Positioning

Type:: BIT
Default value:: yes

This directive tells Bareos not to use block positioning when doing restores. Turning this directive off can cause Bareos to be extremely slow when restoring files. You might use this directive if you wrote your tapes with Bareos in variable block mode (the default), but your drive was in fixed block mode.

Bsf At Eom

Type:: BIT
Default value:: no

If no, no special action is taken by Bareos with the End of Medium (end of tape) is reached because the tape will be positioned after the last EOF tape mark, and Bareos can append to the tape as desired. However, on some systems, such as FreeBSD, when Bareos reads the End of Medium (end of tape), the tape will be positioned after the second EOF tape mark (two successive EOF marks indicated End of Medium). If Bareos appends from that point, all the appended data will be lost. The solution for such systems is to specify Bsf At Eom (Sd->Device) = yes which causes Bareos to backspace over the second EOF mark. Determination of whether or not you need this directive is done using the test command in the btape program.

Changer Command

Type:: STRNAME

This directive can be specified if this device is used with an autochanger and you want to overwrite the default Changer Command (Sd->Autochanger). Normally, this directive will be specified only in the Autochanger Resource, which is then used for all devices. However, you may also specify the different Changer Command in each Device resource.

Changer Device

Type:: STRNAME

This directive should be specified if

this device is used with an autochanger and you want to overwrite the default Changer Device (Sd->Autochanger) or
if you have a standard tape drive and want to use the Alert Command (Sd->Device).

The specified device must be a generic SCSI device.

For details, see the Autochanger & Tape drive Support chapter.

Check Labels

Type:: BIT
Default value:: no
Since Version:: deprecated

If you intend to read ANSI or IBM labels, this must be set. Even if the volume is not ANSI labeled, you can set this to yes, and Bareos will check the label type. Without this directive set to yes, Bareos will assume that labels are of Bareos type and will not check for ANSI or IBM labels. In other words, if there is a possibility of Bareos encountering an ANSI/IBM label, you must set this to yes.

Close On Poll

Type:: BIT
Default value:: no

If Yes, Bareos close the device (equivalent to an unmount except no mount is required) and reopen it at each poll. Normally this is not too useful unless you have the Offline on Unmount directive set, in which case the drive will be taken offline preventing wear on the tape during any future polling. Once the operator inserts a new tape, Bareos will recognize the drive on the next poll and automatically continue with the backup. Please see above for more details.

Collect Statistics

Type:: BOOLEAN
Default value:: yes

Count

Type:: PINT32
Default value:: 1

If Count is set to (1 < Count < 10000), this resource will be multiplied Count times. The names of multiplied resources will have a serial number (0001, 0002, …) attached. If set to 1 only this single resource will be used and its name will not be altered.

Description

Type:: STRING

The Description directive provides easier human recognition, but is not used by Bareos directly.

Device Options

Type:: STRING
Since Version:: 15.2.0

Some Device Type (Sd->Device) require additional configuration. This can be specified in this directive, e.g. for

Droplet Storage Backend GFAPI Storage Backend

Before the Device Options directive have been introduced, these options have to be configured in the Archive Device (Sd->Device) directive. This behavior have changed with Version >= 15.2.0.

Device Type

Type:: STRING

The Device Type specification allows you to explicitly define the kind of device you want to use. It may be one of the following:

Tape

is used to access tape device and thus has sequential access. Tape devices are controlled using ioctl() calls.

File

tells Bareos that the device is a file. It may either be a file defined on fixed medium or a removable filesystem such as USB. All files must be random access devices.

Fifo

is a first-in-first-out sequential access read-only or write-only device.

GFAPI (GlusterFS)

is used to access a GlusterFS storage. It must be configured using Device Options (Sd->Device). For details, refer to GFAPI Storage Backend.

Version >= 14.2.2

Droplet

is used to access an object store supported by libdroplet, most notably S3. For details, refer to Droplet Storage Backend.

Version >= 17.2.7

The Device Type directive is not required in all cases. If it is not specified, Bareos will attempt to guess what kind of device has been specified using the Archive Device (Sd->Device) specification supplied. There are several advantages to explicitly specifying the Device Type. First, on some systems, block and character devices have the same type. Secondly, if you explicitly specify the Device Type, the mount point need not be defined until the device is opened. This is the case with most removable devices such as USB. If the Device Type is not explicitly specified, then the mount point must exist when the Storage daemon starts.

Diagnostic Device

Type:: STRNAME

Drive Crypto Enabled

Type:: BOOLEAN

The default for this directive is No. If Yes the storage daemon can perform so called Application Managed Encryption (AME) using a special Storage Daemon plugin which loads and clears the Encryption key using the SCSI SPIN/SPOUT protocol.

Drive Index

Type:: PINT16

The Drive Index that you specify is passed to the Changer Command (Sd->Device). By default, the Drive Index is zero, so if you have only one drive in your autochanger, everything will work normally. However, if you have multiple drives, you must specify multiple Bareos Device resources (one for each drive). The first Device should have the Drive Index set to 0, and the second Device Resource should contain a Drive Index set to 1, and so on. This will then permit you to use two or more drives in your autochanger.

For details, refer to Multiple Devices.

Drive Tape Alert Enabled

Type:: BOOLEAN

Eof On Error Is Eot

Type:: BOOLEAN
Since Version:: 18.2.4

If Yes, Bareos will treat any read error at an end-of-file mark as end-of-tape. You should only set this option if your tape-drive fails to detect end-of-tape while reading.

Fast Forward Space File

Type:: BIT
Default value:: yes

If No, the archive device is not required to support keeping track of the file number (MTIOCGET ioctl) during forward space file. If Yes, the archive device must support the tt ioctl tt MTFSF call, which virtually all drivers support, but in addition, your SCSI driver must keep track of the file number on the tape and report it back correctly by the MTIOCGET ioctl. Note, some SCSI drivers will correctly forward space, but they do not keep track of the file number or more seriously, they do not report end of medium.

Forward Space File

Type:: BIT
Default value:: yes

If Yes, the archive device must support the tt MTFSF ioctl to forward space by file marks. If No, data must be read to advance the position on the device.

Forward Space Record

Type:: BIT
Default value:: yes

If Yes, the archive device must support the MTFSR ioctl to forward space over records. If No, data must be read in order to advance the position on the device.

Hardware End Of File

Type:: BIT
Default value:: yes

Hardware End Of Medium

Type:: BIT
Default value:: yes

All modern (after 1998) tape drives should support this feature. In doubt, use the btape program to test your drive to see whether or not it supports this function. If the archive device does not support the end of medium ioctl request tt MTEOM, set this parameter to No. The storage daemon will then use the forward space file function to find the end of the recorded data. In addition, your SCSI driver must keep track of the file number on the tape and report it back correctly by the MTIOCGET ioctl. Note, some SCSI drivers will correctly forward space to the end of the recorded data, but they do not keep track of the file number. On Linux machines, the SCSI driver has a fast-eod option, which if set will cause the driver to lose track of the file number. You should ensure that this option is always turned off using the mt program.

Label Block Size

Type:: PINT32
Default value:: 64512

The storage daemon will write the label blocks with the size configured here. Usually, you will not need to change this directive.

For more information on this directive, please see Tapespeed and blocksizes.

Label Media

Type:: BIT
Default value:: no

If Yes, permits this device to automatically label blank media without an explicit operator command. It does so by using an internal algorithm as defined on the Label Format (Dir->Pool) record in each Pool resource. If this is No as by default, Bareos will label tapes only by specific operator command (label in the Console) or when the tape has been recycled. The automatic labeling feature is most useful when writing to disk rather than tape volumes.

Label Type

Type:: LABEL
Since Version:: deprecated

Defines the label type to use, see section Tape Labels: ANSI or IBM. This directive is implemented in the Director Pool resource (Label Type (Dir->Pool)) and in the SD Device resource. If it is specified in the the SD Device resource, it will take precedence over the value passed from the Director to the SD. If it is set to a non-default value, make sure to also enable Check Labels (Sd->Device).

Maximum Block Size

Type:: MAX_BLOCKSIZE
Default value:: 1048576

The Storage daemon will always attempt to write blocks of the specified size (in bytes) to the archive device. As a consequence, this statement specifies both the default block size and the maximum block size. The size written never exceeds the given size. If adding data to a block would cause it to exceed the given maximum size, the block will be written to the archive device, and the new data will begin a new block.

In Bareos Version >= 23.0.0 the default value is 1 MiB (1.048.576 bytes). Volumes written with older versions (and the smaller default block size) are still readable and will be rewritten with the larger block size.

Please read chapter Tapespeed and blocksizes, to see how to tune this value in a safe manner.

Limitation: Setting Maximum Block Size for non-tapes is not supported

This setting has only been tested with tape drives. The use with every other storage backend is untested and therefore unsupported and discouraged.

Warning

After setting this value the device may write volumes with the new setting. Such volumes can only be read by a device with the same or a larger maximum block size configured. You must make sure that all devices with the same Media Type (Sd->Device) have the same value applied.

Maximum Changer Wait

Type:: TIME
Default value:: 300

This directive specifies the maximum amount of time that Bareos will wait for the changer to respond to a command (e.g. load). If you have a slow autoloader you may want to set it longer.

If the autoloader program fails to respond in this time, Bareos will invalidate the volume slot number stored in the catalog and try again. If no additional changer volumes exist, Bareos will ask the operator to intervene.

Maximum Concurrent Jobs

Type:: PINT32
Default value:: 1

This directive specifies the maximum number of Jobs that can run concurrently on a specified Device. Using this directive, it is possible to have different Jobs using multiple drives, because when the Maximum Concurrent Jobs limit is reached, the Storage Daemon will start new Jobs on any other available compatible drive. This facilitates writing to multiple drives with multiple Jobs that all use the same Pool.

Warning

If Device Type (Sd->Device) is “Droplet” then Maximum Concurrent Jobs is limited to 1.

Warning

When using devices that are not of type tape, it is highly recommended to set Maximum Concurrent Jobs to 1 to avoid intermixing jobs. Intermixed jobs on a Volume will significantly reduce performance during restore. Instead, define as many devices as required (e.g. multiply disk devices via Count (Sd->Device)) and parallelize by storing each job to an individual device at once.

Maximum File Size

Type:: SIZE64
Default value:: 1000000000

No more than size bytes will be written into a given logical file on the volume. Once this size is reached, an end of file mark is written on the volume and subsequent data are written into the next file. Breaking long sequences of data blocks with file marks permits quicker positioning to the start of a given stream of data and can improve recovery from read errors on the volume. The default is one Gigabyte. This directive creates EOF marks only on tape media. However, regardless of the medium type (tape, disk, USB …) each time a the Maximum File Size is exceeded, a record is put into the catalog database that permits seeking to that position on the medium for restore operations. If you set this to a small value (e.g. 1MB), you will generate lots of database records (JobMedia) and may significantly increase CPU/disk overhead.

If you are configuring an modern drive like LTO-4 or newer, you probably will want to set the Maximum File Size to 20GB or bigger to avoid making the drive stop to write an EOF mark.

For more info regarding this parameter, read Tapespeed and blocksizes.

Note, this directive does not limit the size of Volumes that Bareos will create regardless of whether they are tape or disk volumes. It changes only the number of EOF marks on a tape and the number of block positioning records that are generated. If you want to limit the size of all Volumes for a particular device, use the use the Maximum Volume Bytes (Dir->Pool) directive.

Maximum Job Spool Size

Type:: SIZE64

where the bytes specify the maximum spool size for any one job that is running. The default is no limit.

Maximum Network Buffer Size

Type:: PINT32

Replaced by MaximumNetworkBufferSize (SD->Storage).

Maximum Open Volumes

Type:: PINT32
Default value:: 1

Maximum Open Wait

Type:: TIME
Default value:: 300

This directive specifies the maximum amount of time that Bareos will wait for a device that is busy. If the device cannot be obtained, the current Job will be terminated in error. Bareos will re-attempt to open the drive the next time a Job starts that needs the the drive.

Maximum Rewind Wait

Type:: TIME
Default value:: 300

This directive specifies the maximum time in seconds for Bareos to wait for a rewind before timing out. If this time is exceeded, Bareos will cancel the job.

Maximum Spool Size

Type:: SIZE64

where the bytes specify the maximum spool size for all jobs that are running. The default is no limit.

Media Type

Required:: True
Type:: STRNAME

The specified value names the type of media supported by this device, for example, “DLT7000”. Media type names are arbitrary in that you set them to anything you want, but they must be known to the volume database to keep track of which storage daemons can read which volumes. In general, each different storage type should have a unique Media Type associated with it. The same name-string must appear in the appropriate Storage resource definition in the Director’s configuration file.

Even though the names you assign are arbitrary (i.e. you choose the name you want), you should take care in specifying them because the Media Type is used to determine which storage device Bareos will select during restore. Thus you should probably use the same Media Type specification for all drives where the Media can be freely interchanged. This is not generally an issue if you have a single Storage daemon, but it is with multiple Storage daemons, especially if they have incompatible media.

For example, if you specify a Media Type of “DDS-4” then during the restore, Bareos will be able to choose any Storage Daemon that handles “DDS-4”. If you have an autochanger, you might want to name the Media Type in a way that is unique to the autochanger, unless you wish to possibly use the Volumes in other drives. You should also ensure to have unique Media Type names if the Media is not compatible between drives. This specification is required for all devices.

In addition, if you are using disk storage, each Device resource will generally have a different mount point or directory. In order for Bareos to select the correct Device resource, each one must have a unique Media Type.

Minimum Block Size

Type:: PINT32

This statement applies only to non-random access devices (e.g. tape drives). Blocks written by the storage daemon to a non-random archive device will never be smaller than the given size. The Storage daemon will attempt to efficiently fill blocks with data received from active sessions but will, if necessary, add padding to a block to achieve the required minimum size.

To force the block size to be fixed, as is the case for some non-random access devices (tape drives), set the Minimum block size and the Maximum block size to the same value. This is usually not required. The default is that the minimum block size is zero and maximum block size is 1 MiB (1.048.576 bytes). This results in a default block size of 1 MiB (1.048.576 bytes).

For example, suppose you want a fixed block size of 100K bytes, then you would specify:

Minimum block size = 100K
Maximum block size = 100K

Please note that if you specify a fixed block size as shown above, the tape drive must either be in variable block size mode, or if it is in fixed block size mode, the block size (generally defined by mt) must be identical to the size specified in Bareos – otherwise when you attempt to re-read your Volumes, you will get an error.

If you want the block size to be variable but with a 63K minimum and 200K maximum (and default as well), you would specify:

Minimum block size =  63K
Maximum block size = 200K

Mount Command

Type:: STRNAME

This directive specifies the command that must be executed to mount devices such as many USB devices. Before the command is executed, %a is replaced with the Archive Device, and %m with the Mount Point.

See the Edit Codes for Mount and Unmount Directives section below for more details of the editing codes that can be used in this directive.

If you need to specify multiple commands, create a shell script.

Mount Point

Type:: STRNAME

Directory where the device can be mounted. This directive is used only for devices that have Requires Mount enabled such as USB file devices.

Name

Required:: True
Type:: NAME

Unique identifier of the resource.

Specifies the Name that the Director will use when asking to backup or restore to or from to this device. This is the logical Device name, and may be any string up to 127 characters in length. It is generally a good idea to make it correspond to the English name of the backup device. The physical name of the device is specified on the Archive Device (Sd->Device) directive. The name you specify here is also used in your Director’s configuration file on the Storage Resource in its Storage resource.

No Rewind On Close

Type:: BOOLEAN
Default value:: yes

If Yes the storage daemon will not try to rewind the device on closing the device e.g. when shutting down the Storage daemon. This allows you to do an emergency shutdown of the Daemon without the need to wait for the device to rewind. On restarting and opening the device it will get a rewind anyhow and this way services don’t have to wait forever for a tape to spool back.

Offline On Unmount

Type:: BIT
Default value:: no

If Yes the archive device must support the tt MTOFFL ioctl to rewind and take the volume offline. In this case, Bareos will issue the offline (eject) request before closing the device during the unmount command. If No Bareos will not attempt to offline the device before unmounting it. After an offline is issued, the cassette will be ejected thus requiring operator intervention to continue, and on some systems require an explicit load command to be issued (mt -f /dev/xxx load) before the system will recognize the tape. If you are using an autochanger, some devices require an offline to be issued prior to changing the volume. However, most devices do not and may get very confused.

If you are using a Linux 2.6 kernel or other OSes such as FreeBSD or Solaris, the Offline On Unmount will leave the drive with no tape, and Bareos will not be able to properly open the drive and may fail the job.

Query Crypto Status

Type:: BOOLEAN

The default for this directive is No. If Yes the storage daemon may query the tape device for it security status. This only makes sense when Drive Crypto Enabled is also set to yes as the actual query is performed by the same Storage Daemon plugin and using the same SCSI SPIN protocol.

Random Access

Type:: BIT
Default value:: no

If Yes, the archive device is assumed to be a random access medium which supports the lseek (or lseek64 if Largefile is enabled during configuration) facility. This should be set to Yes for all file systems such as USB, and fixed files. It should be set to No for non-random access devices such as tapes and named pipes.

Removable Media

Type:: BIT
Default value:: yes

If Yes, this device supports removable media (for example tapes). If No, media cannot be removed (for example, an intermediate backup area on a hard disk). If Removable media is enabled on a File device (as opposed to a tape) the Storage daemon will assume that device may be something like a USB device that can be removed or a simply a removable harddisk. When attempting to open such a device, if the Volume is not found (for File devices, the Volume name is the same as the Filename), then the Storage daemon will search the entire device looking for likely Volume names, and for each one found, it will ask the Director if the Volume can be used. If so, the Storage daemon will use the first such Volume found. Thus it acts somewhat like a tape drive – if the correct Volume is not found, it looks at what actually is found, and if it is an appendable Volume, it will use it.

If the removable medium is not automatically mounted (e.g. udev), then you might consider using additional Storage daemon device directives such as Requires Mount, Mount Point, Mount Command, and Unmount Command, all of which can be used in conjunction with Removable Media.

Requires Mount

Type:: BIT
Default value:: no

When this directive is enabled, the Storage daemon will submit a Mount Command before attempting to open the device. You must set this directive to yes for removable file systems such as USB devices that are not automatically mounted by the operating system when plugged in or opened by Bareos. It should be set to no for all other devices such as tapes and fixed filesystems. It should also be set to no for any removable device that is automatically mounted by the operating system when opened (e.g. USB devices mounted by udev or hotplug). This directive indicates if the device requires to be mounted using the Mount Command. To be able to write devices need a mount, the following directives must also be defined: Mount Point, Mount Command, and Unmount Command.

Spool Directory

Type:: DIRECTORY

specifies the name of the directory to be used to store the spool files for this device. This directory is also used to store temporary part files when writing to a device that requires mount (USB). The default is to use the working directory.

Two Eof

Type:: BIT
Default value:: no

If Yes, Bareos will write two end of file marks when terminating a tape – i.e. after the last job or at the end of the medium. If No, Bareos will only write one end of file to terminate the tape.

Unmount Command

Type:: STRNAME

This directive specifies the command that must be executed to unmount devices such as many USB devices. Before the command is executed, %a is replaced with the Archive Device, and %m with the Mount Point.

Most frequently, you will define it as follows:

Unmount Command = "/bin/umount %m"

See the Edit Codes for Mount and Unmount Directives section below for more details of the editing codes that can be used in this directive.

If you need to specify multiple commands, create a shell script.

Use Mtiocget

Type:: BIT
Default value:: yes

If No, the operating system is not required to support keeping track of the file number and reporting it in the (MTIOCGET ioctl). If you must set this to No, Bareos will do the proper file position determination, but it is very unfortunate because it means that tape movement is very inefficient. Fortunately, this operation system deficiency seems to be the case only on a few *BSD systems. Operating systems known to work correctly are Solaris, Linux and FreeBSD.

Volume Capacity

Type:: SIZE64

Volume Poll Interval

Type:: TIME
Default value:: 300

If the time specified on this directive is non-zero, Bareos will periodically poll (or read) the drive at the specified interval to see if a new volume has been mounted. If the time interval is zero, no polling will occur. This directive can be useful if you want to avoid operator intervention via the console. Instead, the operator can simply remove the old volume and insert the requested one, and Bareos on the next poll will recognize the new tape and continue. Please be aware that if you set this interval too small, you may excessively wear your tape drive if the old tape remains in the drive, since Bareos will read it on each poll.

Edit Codes for Mount and Unmount Directives

Before submitting the Mount Command, or Unmount Command directives to the operating system, Bareos performs character substitution of the following characters:

%% = %
%a = Archive device name
%e = erase (set if cannot mount and first part)
%n = part number
%m = mount point
%v = last part name (i.e. filename)

Devices that require a mount (USB)

Requires Mount (Sd->Device)

You must set this directive to yes for removable devices such as USB unless they are automounted, and to no for all other devices (tapes/files). This directive indicates if the device requires to be mounted to be read, and if it must be written in a special way. If it set, Mount Point (Sd->Device), Mount Command (Sd->Device) and Unmount Command (Sd->Device)directives must also be defined.

Mount Point (Sd->Device)

Directory where the device can be mounted.

Mount Command (Sd->Device)

Command that must be executed to mount the device. Before the command is executed, %a is replaced with the Archive Device, and %m with the Mount Point.

Most frequently, you will define it as follows:

Mount Command = "/bin/mount -t iso9660 -o ro %a %m"

For some media, you may need multiple commands. If so, it is recommended that you use a shell script instead of putting them all into the Mount Command. For example, instead of this:

Mount Command = "/usr/local/bin/mymount"

Where that script contains:

#!/bin/sh
ndasadmin enable -s 1 -o w
sleep 2
mount /dev/ndas-00323794-0p1 /backup

Similar consideration should be given to all other Command parameters.

Unmount Command (Sd->Device)

Command that must be executed to unmount the device. Before the command is executed, %a is replaced with the Archive Device, and %m with the Mount Point.

Most frequently, you will define it as follows:

Unmount Command = "/bin/umount %m"

If you need to specify multiple commands, create a shell script.

Autochanger Resource

The Autochanger resource supports single or multiple drive autochangers by grouping one or more Device resources into one unit called an autochanger in Bareos (often referred to as a “tape library” by autochanger manufacturers).

configuration directive name	type of data	remark
`Changer Command (Sd->Autochanger)`	= `STRNAME`	required
`Changer Device (Sd->Autochanger)`	= `STRNAME`	required
`Description (Sd->Autochanger)`	= `STRING`
`Device (Sd->Autochanger)`	= `RESOURCE_LIST`	required
`Name (Sd->Autochanger)`	= `NAME`	required

Changer Command

Required:: True
Type:: STRNAME

This command specifies an external program and parameter to be called that will automatically change volumes as required by Bareos. This command is invoked each time that Bareos wishes to manipulate the autochanger.

Most frequently, you will specify the Bareos supplied mtx-changer script.

The following substitutions are made in the command before it is sent to the operating system for execution:

%%: %
%a: archive device name
%c: changer device name
%d: changer drive index base 0
%f: Client’s name
%j: Job name
%o: command (loaded, load, or unload)
%s: Slot base 0
%S: Slot base 1
%v: Volume name

A typical setting for this is Changer Command (Sd->Autochanger) = "/usr/lib/bareos/scripts/mtx-changer %c %o %S %a %d".

Details of the three commands currently used by Bareos (loaded, load, unload) as well as the output expected by Bareos are given in the Bareos Autochanger Interface section.

If it is specified here, it needs not to be specified in the Device resource. If it is also specified in the Device resource, it will take precedence over the one specified in the Autochanger resource.

Changer Device

Required:: True
Type:: STRNAME

The specified device must be the generic SCSI device of the autochanger.

The changer device is additional to the the Archive Device (Sd->Device). This is because most autochangers are controlled through a different device than is used for reading and writing the tapes. For example, on Linux, one normally uses the generic SCSI interface for controlling the autochanger, but the standard SCSI interface for reading and writing the tapes.

On Linux, for the Archive Device (Sd->Device) = /dev/nst0, you would typically have Changer Device (Sd->Device) = /dev/sg0.

On FreeBSD systems, the changer device will typically be on /dev/pass0 through /dev/passN.

On Solaris, the changer device will typically be some file under /dev/rdsk.

Please ensure that your Storage daemon has permission to access this device.

It can be overwritten per device using the Changer Device (Sd->Device) directive.

Description

Type:: STRING

Device

Required:: True
Type:: RESOURCE_LIST

Specifies the names of the Device resource or resources that correspond to the autochanger drive. If you have a multiple drive autochanger, you must specify multiple Device names, each one referring to a separate Device resource that contains a Drive Index specification that corresponds to the drive number base zero. You may specify multiple device names on a single line separated by commas, and/or you may specify multiple Device directives.

Name

Required:: True
Type:: NAME

Specifies the Name of the Autochanger. This name is used in the Director’s Storage definition to refer to the autochanger.

The following is an example of a valid Autochanger resource definition:

Autochanger Configuration Example

Autochanger {
  Name = "DDS-4-changer"
  Device = DDS-4-1, DDS-4-2, DDS-4-3
  Changer Device = /dev/sg0
  Changer Command = "/usr/lib/bareos/scripts/mtx-changer %c %o %S %a %d"
}
Device {
  Name = "DDS-4-1"
  Drive Index = 0
  Autochanger = yes
  ...
}
Device {
  Name = "DDS-4-2"
  Drive Index = 1
  Autochanger = yes
  ...
Device {
  Name = "DDS-4-3"
  Drive Index = 2
  Autochanger = yes
  Autoselect = no
  ...
}

Please note that it is important to include the Autochanger (Sd->Device) = yes directive in each device definition that belongs to an Autochanger. A device definition should not belong to more than one Autochanger resource.

Also, your Device (Dir->Storage) must refer to the Autochanger’s resource name rather than a name of one of the Devices.

For details refer to the Autochanger & Tape drive Support chapter.

Multiplied Device

The Multiplied Device feature can be used when multiple identical devices are needed. In this case the Count (Sd->Device) can be added to the regarding Device resource.

When the configuration is loaded the Bareos Storage Daemon will then automatically multiply this device Count (Sd->Device) times. The number of multiplied devices includes the original Device.

A number “0001” will be appended to name of the initial Device. All other multiplied Devices have increasing numbers “0002”, “0003”, accordingly. In the example below the name of the multiplied devices will be “MultiFileStorage0001”, “MultiFileStorage0002”, and so on.

bareos-sd.d/device/multiplied_device.conf

Device {
  #Multiply this device Count times
  Count = 3

  Name = MultiFileStorage
  Media Type = File
  Archive Device = /home/testuser/multiplied-device-test/storage
  LabelMedia = yes                   # lets Bareos label unlabeled media
  Random Access = yes
  AutomaticMount = yes               # when device opened, read it
  RemovableMedia = no
  AlwaysOpen = no
  Description = "File device. Will be multiplied 3 times"
}

In the Bareos Director any of the Multiplied Devices can be referred to using their numbered names.

However, in the autochanger resource of the Bareos Storage Daemon the original name of the initial Multiplied Device Resource can be used.

bareos-sd.d/autochanger/autochanger.conf

Autochanger {
  Name = "virtual-autochanger"

  # list here only the name of the initial multiplied device resource
  Device = MultiFileStorage

  Changer Device = /dev/null
  Changer Command = ""
}

When the configuration is exported, again only the name of the initial Multiplied Device Resource will be printed.

Messages Resource

For a description of the Messages Resource, please see the Messages Configuration chapter of this manual.